AUTOMATION OF ADDITIVE PROCESSING METHODS IN THE PRODUCTION OF PRODUCTS MADE OF PHOTOPOLYMER MATERIALS
https://doi.org/10.51955/2312-1327_2023_3_68
Abstract
The use of new modern structural materials that would improve the physical andmechanical properties of products, assemblies and components of machine and transportengineering would reduce the mass fraction of metals in their design, which is a very urgent task.The purpose of this study was to develop an algorithmic solution for the automated control of thetechnology for manufacturing products from photopolymers based on the found scientificallybased set of controlled parameters obtained in the process of studying the physical and mechanicalcharacteristics and chemical properties of composites.
The experimental and industrial tests of the physical and mechanical properties of resin ROEHM R-50 made it possible to investigate the operation of the photopolymerization control system algorithm in practice.
About the Authors
N. G. Filippenko
Irkutsk State Transport University
Russian Federation
Russian Federation
Nikolai G. Filippenko, Candidate of Technical Sciences, Associate Professor
15, Chernyschevskogo street, Irkutsk-74, 664074
A. V. Livshits
Irkutsk State Transport University
Russian Federation
Russian Federation
Alexandr V. Livshits, Doctor of Technical Sciences, Professor
15, Chernyschevskogo street, Irkutsk-74, 664074
T. T. Chumbadze
Irkutsk State Transport University
Russian Federation
Russian Federation
Tamara T. Chumbadze, graduate student
15, Chernyschevskogo street, Irkutsk-74, 664074
References
1. Averina Y. M. Kurbatov A. Y., Sakharov D. A., Subcheva E. N. (2020). Development of nanofiltration ceramic membrane production technology. Glass and Ceramics. 77(3-4): 98-102.
2. Boissonneault T. (2020). Metal AM Focus. Additive manufacturing industry: metal. 3D Printing Media Network, 2020. 27 c.
3. Dumchev I. S. Larchenko A. G., Popov S. I., Filippenko N. G., Livshits A.V. (2012). Restoration of polyamide separators of bearings of the axle box assembly of rolling stock of JSC Russian Railways. Young Scientist. 12: 48-51. (In Russian)
4. Finogeev D. Yu., Reshetnikova O. P. (2020). Additive technologies in modern production of precision engineering parts. Bulletin of the Saratov State Technical University. 3 (86): 63-71. (In Russian)
5. Kamaev S. V., Markov M. A., Nikitin A. N., Novikov M. M. (2018). Laser stereolithography: state and prospects. Additive technologies. 4: 44-48. (In Russian)
6. Lipson H., Kurman M. (2013). Fabricated: The new world of 3D printing. John Wiley & Sons Limited. 2013. 320 p.
7. Livshits A. V., Filippenko N. G., Larchenko A. G., Filatova S. N. (2014). High-frequency electrothermal processing of nonmetallic secondary raw materials. Science and Education: scientific edition Bauman Moscow State Technical University. 6: 55-65. (In Russian)
8. Raevsky E. V., Tsygankova A. L. (2016). The technology of laser sintering of metal has reached a new level of industrial application. Additive technologies. 1: 13-15. (In Russian)
9. Rikhirev M. I. (2020). Digital additive ruler. Additive technologies. 3: 18-26. (In Russian)
10. Rybina E. O., Averina Yu. M., Kalyakina G. E., Subcheva E. N. (2018). Methods of obtaining ceramic composite membranes with nano- and micropores. Eurasian Scientific Association. 6-1(40): 41-43. (In Russian)
Review
For citations:
Filippenko N.G., Livshits A.V., Chumbadze T.T. AUTOMATION OF ADDITIVE PROCESSING METHODS IN THE PRODUCTION OF PRODUCTS MADE OF PHOTOPOLYMER MATERIALS. Crede Experto: transport, society, education, language. 2023;(3):68-77. (In Russ.) https://doi.org/10.51955/2312-1327_2023_3_68
Views:
7
JATS XML
Email this article 